Founded in 2008,Bazhou Sanqiang Metal Articles Co.,Ltd.is a professional enterprise specializing in manufacturing cold-rolled strip steel and galvanized strip steel,register funds RMB 20 million yuan with the area of 500 Mu.There are more than 500 staffs and 180 of which are key technicians.
The company now owned 11 sets of cold-rolled equipment ,such as AGC 650# 6-roller reversible rollig equipment, 650 # 4-roller reversible rollig equipment,850 reversible rollig equipment,600 and750 5-Stand and 5-continuous, and 8 sets of the different types cutting mill, 2 sets of 750 finishing mill, 1 set of 750 flattening mill,24 groups of hood type bright annealing furnace and 4 sets of tunnel annealing furnace. On these bases, in order to meet customer demands, the company had introduced 3 advanced galvanized block production line and 1 tinning block production line. Advanced production equipment, strict management ensure the quality of product …
We take the pleasure to introduce overselves as one the largest IMPORTERS, STOCK HOLDERS & SUPPLIERS for the following materials:
STAINLESS STEEL, SHEET, PLATES, COILS, TUBES, PIPES, RODS, WIRES, FLATS, STRUCTURAL, FITTINGS, FLANGES etc.
Confirming to TP-202, 304, 304L, 309, 310, 310S, 316, 316S, 316TI, 321, 410, 430, 904L, NICKLE, MONEL, INCONEL, TITANIUM & ALL HIGH NICKLE GRADES.
ALL ITEMS IN BRASS, COPPER, ALUMINUM, CARBON STEEL, MILD STEEL & BOILER QUALITY (BQ) ITEMS.
We are regularly supplying these items to many leading industrial Units consisting of CHEMICALS, FERTILIZERS, PETROCHEMICAL PLANTS, REFINERIES, PAPER MILLS, CEMENT PLANTS, SUGAR MILL, FABRICATION UNITS etc.
We also supply these items especially Stainless Steel Sheets/ Plates/ Coils/ Pipes to Engineering Industries who are engage in the Manufacture and fabrication of Process Equipment. We can supply the Items even under third party inspection viz BUREAU VERITAS, D.N.V. H&G, KAVERNOR POWER GAS, UDHE INDIA, EIL, LLOYDS, TOYO, CHEMTEX, CEIL, TECNIMONT ICB & IBR etc.
As we are regularly maintaining bulk stock in every item, we can arrange supplies in time and that too at the most competitive rates. We shall be thank full to you to kindly enlist our name with your approved Vendor list and favor us with your valuable enquires against your regular requirements.
We would appreciate to get your esteemed enquires and look forward to the pleasure receiving your valuable response.
Thanking you and assuring our best services at all times.
Tianjin Long Feng Yuan Metal Material Trade Co., Ltd is the subsididary company of HUAYE GROUP LTD founded in 2004, China. It is engaged in steel trading, retailing, processing and distributing as one of the professional companies.
Our company main product:hot dip galvanized steel,color coated coils,tin plate, pickling coil,cold-rolled plate and other relative steel products. Our management objective is “Down to earth, hold the world with virtue”. We already established a long-term stable relationship with a lot retailers and agents for many years. Our company is powerful. We win the trust of our customers with good credit and high quality products.
Our customers are from the entire world, such as, Southeast Asia, Africa, South America, Middle East, and Europe. Main importing countries like Korean, Chile, Turkey, Brazil, Singapore, Australia, Spain, Ukraine, Russia, Thailand, Philippines, India, UAE, Saudi Arabia and so on.
We are looking forward to forming successful business relationships with new clients around the world in the near future.
Welcome to Rama Group, One of the leading manufactures of Steel Pipes & Tubes and Rigid PVC & G.I. Pipes in India. Established in 1974 by Sh. H.L. Bansal, Rama in one of the most trusted and established name in the Steel Tube and pipe market in India, and one which in rapidly gaining recognition in overseas markers.
With its 20% exports rate, the company has global presence in the Countries like United Kingdom, UAE, Sri Lanka, Ethiopia, Kenya, Uganda, Ghana, Kuwait, Republic of Congo, Yemen, Guyana, Germany, USA, South Africa, Zambia and Malta etc. being its prime markets.
We make some of the best steel tube products in India. Our range includes MS ERW black pipes from 15mm to 200mm diameter pipes confirming to IS: 1239, IS:1161, IS:3589, IS:3601, & IS:4270 and G.I. Pipes from 15mm to 150mm NB in light, medium and heavy sizes.
As a pioneer and leader in the steel tubes industry, Rama is at the forefront of technology and research. We are constantly innovating, listening to the rapidly changing market and giving the consumer the best value for his money. It is our vision to build lasting relationships with our vendors, partners, suppliers, associates, employees, customers and stock holders. We believe that anyone who comes in contact with Rama must experience delight and satisfaction.
We are Rama, where every effort is towards being better – than the best.
Rama has developed a very sophisticated manufacturing facility and the company constantly invests in the latest advances in technology.
To take the lead & full fill the market demand Rama Group has installed a modern high speed Tube Mill based on latest technology of world leader M/s Kusakabe of Japan
These investments not only ensure superior products for our customers but also enhance our leadership position in the region Rama also has a well-equipped workshop with skilled technicians to the specific requirement of customers.
Customer know that they can depend on our family owned and operated company to strive to deliver quality products on time every time. We value long-term relationships and work to be the best possible supplier to our customers.
Rama Group has the world’s latest technology plant and machinery, which also includes sophisticated testing equipments. Our plants is 10 Kilometers form New Delhi, India’s national capital, in the industrial belt of Sahibabad. While technology is never compromised, we at Rama believe that it is not just technology that makes us a force to reckon with. It is our people who are our biggest assets. We have the finest intellect working for us around the country, highly qualified engineers hired from the best institutions in India. Their experience and expertise goes into the making of our products.
INDUSTRIAL TUBES INDIA established in the year 1975 and is now the leading supplier and importer of ferrous & non-ferrous products specializing in stainless steel products. AMAR SALES CORPORATION , a sister concern of industrial tubes india is primarily engaged in importing and stocking of all kinds of stainless steel, carbon steel and other industrial raw material in the form of pipe,plates,sheets coils, fittings, rods,bars,angels etc.
We have huge & ready stock of various ferrous products in all grades, shapes & sizes. Precisely we have products of all fields of application. this enables us to cater to our customers requirements at the least possible time & at most competitive price. Actually we work as a one stop shop for all your industrial product requirements.
We dedicate our company’s success & the growing customer confidence in us to our work ethics & business integrity. Even in today’s competitive world however demanding the situtations we always stand on the right side of business practice.
For our customer’s benfit, besides competitive pricing, assured quality & prompt supply, we assure you our best & dedicated services & look forward to building up a long & lasting business relation.
Your search for stainless steel ends here.
MAIN STEEL GRADES as follows:
-high quality carbon and alloy steels
-modern carburizing steel
-boron steel
-bearing quality steel
-stainless and heat resisting steel
-structural steels with micro alloy additions
Example grades for plates 3-30mm:
Hadfield (X120mn12), Armour, Hardstal (wear resisting plates)…
Good Luck Steel Tubes Ltd. engages in manufacturing and exporting of a wide range of galvanized sheets & coils, towers, hollow sections, CR coils and pipes & tubes. The company specializes in providing Telecommunication Structures, ERW Steel Tubes, ERW Steel Pipes, and Galvanized Black Steel Tubes. Incorporated in 1986, the company is based in Delhi.
Company is coking, sintering, smelting, rolled, and research and development as integrated large iron and steel company. Its products include plate, high speed wire rod, formed materials with more than 30 varieties over 2000 steel products and coke chemical products. The main equipment are 120t converter-steckel, 100t electric furnace, high-speed wire rod mill, 2.8m plate mill, 260 mill and other international or domestic advanced equipment. Main products have passed ISO9002 quality system certification and…
Copper Mould Tube & Plate
We specially in supplying Copper Mould Tube, Crystallizing equipment of continuous casters, Mould cooling jacket, Repair of Metallurgical Copper Mould Tube, etc.
Equipments & Spare parts for Continuous Casting Machine.
- Copper mould tube( square, rectangle and round )
- Crystallizing equipment of continuous casters
- Mould cooling jacket.
- repair of copper tube moulds
The copper alloys chosen for the moulds must maintain their physical properties at the operating temperatures of the continuous casting process.
The temperature gradation from the inner wall of the mould to the outside face of the mould can cause serious distortion problems, and Metallurgical Copper Mould Tube is imperative that the correct alloy is chosen for the various operating conditions.
Square Copper mould tube STANDARD MATERIALS
Phosphorus de-oxidised copper
This alloy has been proven to be excellent for the manufacture of moulds in the continuous casting of billets. The main composition of this alloy are Cu +Ag 99.90min, P0.0015 / 0.040.
Copper -Silver alloy
The addition of a small amount of silver, whilst not increasing the melting point of copper, does increase the recrystallisation temperature by almost 100℃, and also helps to give better thermal conductivity at the operating temperatures.
This alloy is normally used in moulds for the continuous casting of blooms and slabs .In this case, the moulds are much thicker than in the billet moulds, and the moulds temperature can be higher. The main composition of this alloy are Cu+Ag99.90 min. Ag 0.08 / 0.12 O 0.004 / 0.012.
The continuous casting of molten steel into billets, blooms and slab products, has been highly refined over the years into an extremely sophisticated system. The continuous casting process is expected to produce metallurgically sound products at the lower possible cost, and this is being achieved in many steelworks throughout the world.
Copper moulds have played an important role in the development of the continuous casting process. Their funcition is to receive the molten steel and to allow rapid heat transfer from the steel to the cooling water to enable quick solidification.
The mould must exhibit excellent thermal conductivity, be resistant for thermal erosion ,and be resistant to distortion from thermal stress. So far only copper and a few copper alloys meet the above conditions, both economically and technically.
Mould cooling jacket supplier SOLIDIFICATION
The rate of solidification in the continuous casting process dictates the speed of production. The molten steel, which is in contact with the inner faces of the copper mould, starts to sllidify as rapidly as the heat is extracted, forming a shell. The shell increases in thickness as more heat is extracted, and eventually total solidfication is achieved. the process is similar to the solidification of ingots in ingot moulds. In continuous casting, the whole process is speeded up, with the aim to produce and homogeneous shell growth. Consequently, the mould is an important part of the continuous casting process, and the manufactured quality of the mould plays and important role in their length of life.
INNER SURFACE COATINGS
Over the years, Metallurgists and Engineers have been working together to develop better continuous casting moulds. The steel companies require a more economical mould which will give a longer service life. Surface coating of the inner walls of the mould has given the best results to date. Coatings available are Chromium and Nickel plating. Also, a combination of the two give good results on slab casting.
SPECIFICATIONS OF COPPER MOULD
Square 60 x 60 – 350 x 350 (mm)
Rectangle 120 x 160 – 180 x 300 (mm)
Diameter 100-400 (mm)
Size(mm): 90×90, 100×100, 110×110, 115×115, 120×120
130×130, 135×135, 140×140, 143×143, 150×150
155×155, 160×160, 165×165, 175×175, 180×180
200×200, 220×220, 100×170, 100×173, 130×240
150×200, 150×210, 150×220, 160×200, 160×220
150×225, 160×235, 165×225, 175×225, 180×220
200×240, 240×240, 235×235
Radius(mm): 4000, 5000, 5250, 6000, 7000, 7500, 8000, 9000, 10250, 10300, 11000, 12000
Length(mm): 700, 750, 780, 790, 800, 810, 812, 850, 900, 1000
The CSM Group operates since 1988 in processing and trading stainless steel and special alloys.
Centro Servizi Metalli was founded to serve the “Italian Food Valley” and has further expanded its activity in Europe, up to three production units in Italy (Reggio Emilia), Poland (Gliwice) and France (Lyon). The group also has two sales offices in Germany and one in Belgium.
The group has more than 8.000 tons of stock at disposal. The wide range of alloys and thicknesses, the well-equipped production plants and the functional geographical positions around Europe enable a fast and specific service. The cutting is done according to the customers’ projects using water jet, plasma and mechanical cutting technologies.
For more than 25 years BINDER EDELSTAHL has been manufacturing high-quality stainless steel products. Quality, reliability and speed, in combination with intensive consultancy services have been and remain the cornerstones of our success.
MARWA IMPEX PRIVATE LIMITED is one of the prestigious fast developing firms in the field of Import & Export Company in India. It is the mission of MIPL to provide complete import/export services including purchase contracts, shipping and delivery scheduling.
MIPL is situated in Chennai, Tamil Nadu. MIPL is a company engaged in wide range of Iron & Steel, Building Materials, Electrical Items, Vehicles, Safety Equipments, Furniture, Medical Items, Hotel Supplies, etc.
As an exporter & importer, MIPL is able to achieve the confidence of the buyers, by providing them the quality products at best competitive rates with best delivery time. The aim of MIPL is to get total satisfaction of the customers.
MIPL has its associate offices at Singapore and China & has global contacts with various International Companies through which MIPL would be able to supply products from worldwide
Welcome to visit the company, you will find any items that you want in MIPL.
Ferrobend initially known as Anand steel is one of the renowned manufacturer & distributors of industrial pipe, valves, fittings, flanges, fasteners, plates and related products with head office located in Mumbai, India. We service a wide variety of customers in the industrial, mechanical, Oil & Gas, Cement, food processing, pharmaceutical and government sectors. Our goal is to provide quality piping products that are tailored to customer project specification, superior customer service, for the prosperity of communities and nations.
Founded in 1972 by Andrea Perotti, the company has grown rather quickly and today it’s a reference point for the market. Its hight quality standards, flexibility and its fast and punctual service delivery are its great points of strenght.
Glued Steel Fiber, an alternate concrete reinforcing material are high tensile steel wires with hooked ends, glued together by the water-soluble adhesive for compactness and uniform dispersion in concrete, to increase the concrete properties by 3-4 times.
steel fiber reinforced concrete supplier improve the mechanical properties concrete and materials such as ductility,
energy absorption, fatigue, and toughness. This fiber helps to controls plastic shrinkage cracking in concrete; helps reduce or eliminate need for conventional reinforcement.
Application of Glued steel fiber reinforced concrete
- For concrete flooring
Industrial floors
Joint-less floors
Floors-on-piles
Lightly loaded floors
Liquid tight floors & composite metal decking
- stainless steel fiber supplierFor Hard Standing & Heavy Duty
Parking lots
Playgrounds
Airport runways
Taxiways
Maintenance hangers
Access roads & workshops
Ports& Containers for port pavements
Container terminals
Bulk storage areas access roads
For army tank movement
- steel fibers for concrete reinforcementOther Applications
Foundations
Traditional cellar and basement walls
Compression layers
Tunnel engineering
Compared with the GuangYa loose steel fiber the operation and advantages of the glued steel fiber:
- Add the steel fiber directly into the belt, the whole row of steel fiber as a whole, evenly dispersed in the concrete corner
- The water-soluble glue begins to dissolve in a row of steel fibers in the premise of the dispersion, it is again dispersed in every corner of the mono filament fiber, showing the perspective in the concrete of the fiber mesh, which plays an integral strengthening.
- Compared with mono-filament fibers, China bonded steel fiberswill not be bundled to ensure that the fibers in concrete do not coalesce and distribute evenly.
Glued steel fibers are loose hook-end fibers that are bonded together in a row. The great difference between loose fiber and glued fiber is that the former is easy to clog and the latter is easy to disperse evenly.
It is a big cross-regional, cross-industry enterprise group that has diversified business model. Its business covers several industries such as the wire production, construction, real estate, coal processing, machinery manufacturing logistics.The company mainly produces steel wire rope products, through the introduction of international advanced technology and equipment research and development of their own. The company’s wire rope manufacturing technology has the domestic leading level. Ning Xia Huahui…
METALON, UAB – ferrous metals wholesaler. The company’s activity is focused on the Scandinavian and Baltic countries. Professional company’s employees have many years of experience in marketing, production and logistics, which allows to offer our customers excellent service and quality for a reasonable price. All products conforms the European Union standards and are supplied with a confirming quality certificates.
Gratitude to close cooperation and a long-term steady relationships with European Union metal factories METALON, UAB is able to offer a wide range of metal products.
Our customers knows that the metals market is rapidly changing market with frequently fluctuating prices. METALON, UAB choice of business model allows flexibly respond to the changing situation on the market and offer our customers the conditions which corresponds to the current economic situation in the world and Europe.
We look forward for the close cooperation with metal manufacturing, construction and manufacture companies.
Zenith Steel Tubes and Industries Ltd. operates as a pipe manufacturer and dealer, tube manufacturer, and exporter of iron tubes, steel tubes etc. The company was incorporated on March 12, 1984 and its office is located in Mumbai.
Kanishk Steel Industries Ltd., an ISO 9001:2000 certified company listed in BSE. Kanishk Steel is promoted by late Shri. O.P Gupta, who has established steel related business in Tamilnadu.
Kanishk Steel Industries Ltd., has a turnover of Rs.273.93 crores and the group turnover is of Rs.500 Crores. Kanishk Steel employs around 450 people. The company manufactures steel products (Finished goods) both Constructional steel and Structural steel conforming to the Bureau of Indian Standards BIS 1786 and IS 2062 (equivalent to ASTM, BS, DIN).